Filter By:
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
Tools

$110.95
A daily-use, shop version of Park Tool's world-famous CM-5.2 Chain Scrubber. The CM-25 features a super-tough die-cast aluminum case and handle, plus a unique brush/sponge replacement cartridge that makes it easy to keep it running smoothly and working properly. Park Tool's proven four-sided scrubbing action makes thoroughly cleaning chains quick and easy. A shop quality cleaner built to give years of constant use.
- Proven chain scrubbing technology leaves chains sparkling clean
- Durable A380 aluminum die cast case and removable handle
- Dual-sided sponges and wicking pads to help reduce drips
- Rotating brushes clean on all four sides of every link
- Brush and sponge cartridge quickly and easily clicks in and out (RBS-25)
- Locking cover with stainless steel hinge pins
- Choose drip or immersion fluid application methods
- 100% serviceable

$66.95
Park Tool's Thru Axle Adaptors make it possible to adapt all Park Tool Truing Stands to work with 12mm, 15mm, 20mm, and 25mm thru axle front wheels, as well as Cannondale Lefty wheels (each sold separately).
The TS-TA also work with the rear 135mm thru axle hubs in the TS-2.2 and TS-3. The TS-TA when used in the TS-8, TS-25, TS-15, TS-7 or TS-5 will work with all rear thru axle hubs.
For thru axle hubs greater than 135 (142, 150, 157, etc.) in the TS-2.2, use the TS-2TA Thru Axle Adaptors (sold separately).

$65.00
The QTH-1 is an ergonomic T-handled bit driver equipped with eight common bits to fit a wide variety of fasteners and fittings found on bicycles. The magnetic "quick-change" handle allows for one-handed operation and makes changing bits quick and easy. The bit holder can be magnetically attached to any magnetic surface such as a repair stand or tool box, or can be permanently mounted to any wall or tool board. The QTH-1 is a professional-grade tool built to withstand the rigors of daily shop use and is fully rebuildable.
Includes the following magnetic 1/4" bits:
- 2mm, 2.5mm, 3mm, 4mm, 5mm & 6mm hex
- T25 Torx-compatible
- #2 Philips cross tip
- Bit holder includes empty spaces for 2 extra bits

$54.95
Park Tool's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press which is sold separately) BB86, BB90, BB92 and Press Fit bottom brackets from Shimano, Race Face, SRAM and others that use a nominal 24mm-diameter spindle. This tool has a bearing remover that fits inside the bottom bracket shell and into the bearing so the bearings can be tapped out of the frame with a hammer. The set also includes two bushings that you use in conjunction with a bearing press for precision bearing installation (bearing press sold separately).

$54.95
The Park Tool SBS-1.2 is a shop-quality set of sockets, hex bits, and Torx style bits, selected specifically for common bike repair needs. Ideal for use with Park Tool torque wrenches, the SBS-1.2 3/8" drive bits and sockets are made from tough, chrome vanadium steel for lasting durability.

$45.00
A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings.
The Chain Gang includes:
- CM-5.3 Cyclone Chain Scrubber
- GSC-1 GearClean Brush
- 8 oz. bottle of Bio ChainBrite
The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.

$45.00
The MTC-40 features a super strong, composite, multi-position handle, with hardened and plated tools and smooth ergonomic operation. Lightweight, compact, and perfect to carry along.
- 2.5, 3, 4, 5, 6 and 8mm hex wrenches
- T25 & T30 Torx compatible driver
- Combo cross/straight tip screwdriver
- 5- to 12-speed compatible chain tool*
- Rotor straightener
- CO2 cartridge inflator adaptor
- Bottle opener
- Key ring holder
- Weight: 217g (7.65 ounces)
*The MTC-40 chain tool will not peen Campagnolo 11-speed chain rivets (see CT-4.3 or CT-6.3)

$41.95
A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP).
*The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets.
- Comfortable T-handle
- Replaceable driving pin (CTP)
- Investment cast steel body
- Adjustable locating shelf

$41.95
Park Tool's SBS-1 Socket And Bit Set is a shop quality set of sockets, hex bits and Torx bits for the bike mechanic. Ideal for use with Park Tool Torque Wrenches, the SBS-1's 3/8-inch drive bits and sockets are made from tough chrome vanadium steel for long life. The set includes 3, 4, 5, 6, 8 and 10mm hex bits, T25, T30, T40 Torx bits, and 8, 9, 10, 11, 12, 13, 14, 15mm sockets. It also has a 1-inch socket that fits various Park freewheel, cassette lockring, and BB tools and a convenient holder.

$36.00
The HCW-16.3 is a combination 15mm pedal wrench and chain whip. Use for both pedal removal/installation and for cassette removal. Chain whip features improved compatibility with 5-speed to 12-speed mountain and road bike cassettes and freewheels. The HCW-16.3 is 10.75" long (27.3cm).

$35.00
Precision CNC machined aluminum tool for the installation and removal of 12-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8" drive.
- 46mm 12-notch OD cup
- Race Face® Cinch™, Rotor® BSA30, Zipp® Vuma™, Hawk Racing™ BB3086™, and more

$33.95
Park's I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set with Chain Tool includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver, a T25 Torx tool (for disc-rotor bolts), a tire lever, spoke wrenches and a chain tool. The I-Beam conveniently fits in pockets and packs, too.

$32.00
Made from tough steel and reinforced with extra material at the highly stressed wrench openings, Park’s shop-quality Pedal Wrench is built to easily install and remove pedals, and to last and last. It has 15mm and 9/16-inch precision openings to fit all pedals. And it boasts a long, round, vinyl-coated handle that won’t dig into your hand and provides optimum leverage. There's even a hole in the end of the wrench for hanging it on your toolboard.

$30.00
The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.

$30.00
Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts.
- Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes
- Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain
- Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess
- Sturdy handle makes the Cyclone easy to use and control
- Holds 2 fluid ounces (59ml) of solvent

$27.95
The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.

$26.95
• Precision CNC-machined aluminum tool for the installation and removal of external bearing bottom brackets
• Anodized for easy identification and featuring a ratchet/ torque wrench compatible 3/8” drive
• Fits 16 notch adaptors measuring 39mm diameter such as Shimano XTR BB93, Dura Ace BB9000

$26.95
• Precision CNC-machined aluminum tool for the installation and removal of external bearing bottom brackets
• Anodized for easy identification and featuring a ratchet/ torque wrench compatible 3/8” drive
• Fits 16 notch adaptors measuring 41mm diameter such as Shimano BBR60 (Ultegra 11-speed 6800 series)

$26.95
• Precision CNC-machined aluminum tool for the installation and removal of external bearing bottom brackets
• Anodized for easy identification and featuring a ratchet/ torque wrench compatible 3/8” drive
• Fits 16 notch adaptors measuring 44mm diameter such as Shimano BB80, BB5700, XT BB70, BB51, and previous external bearing threaded cups
• Also fits many external threaded types for Campagnolo, Chris King, FSA MegaExo, Hope, SRAM/Truvativ GXP, Race Face X-type, Surly, Wheels, and others
• Fits the lockrings of rotor discs with 16 notches

$26.95
The BBT-29 is a double-ended bottom bracket wrench designed to fit 16-notch bearing cups with an outside diameter of 39mm (e.g. Shimano Dura-Ace 9000 series and XTR 980 series) as well as 16-notch bearing cups with an outside diameter of 48.5mm (e.g. FSA MegaEvo).

$25.00
A clean bike is a happy bike! Park Tool's Bike Cleaning Brush Kit is a four-piece brush set designed specifically to clean bicycles. Ergonomically designed and featuring dual-density, sure-grip handles, the BCB-4.2 kit includes:
• 1 GSC-1 Gear Clean Brush
• 1 Tapered Detail Brush
• 1 Frame Cleaning Sponge/Bristle Brush
• 1 Soft Bristle Soaping Brush

$20.95
Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.

$20.00
Park's Crank Puller is for removing crankarms on Shimano's splined, oversize, pipe-billet bottom brackets. It employs a long handle and a fine thread for the leverage and torque needed to remove tight arms. Park's unique rotating tip ensures smooth operation and long life. (The CCP-44 does not fit standard square or tapered bottom brackets.)

$20.00
The MTC-20 features a super strong, composite, multi-position handle, with hardened and plated tools and smooth ergonomic operation. Lightweight, compact, and perfect to carry along.
- 3, 4, 5 and 8mm hex wrenches
- T25 Torx compatible driver
- Combo cross/straight tip screwdriver
- CO2 cartridge inflator adaptor
- Key ring holder
- Weight: 74g (2.61 ounces)

$19.99
$22.99
13% Off
Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing.
To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap.
Works with the CT-4.3, CT-4.2, CT-4, and CT-11

$19.00
Park's Home Mechanic Pedal Wrench is great for your home workshop and event tool box. This top-quality 15mm pedal wrench provides the leverage you need to remove stubborn pedals. It's made to last from heat-treated steel, and the handle has a vinyl grip for comfort.

$15.95
Park combines the three most used bolt sizes into one convenient wrench. The 3-Way Sprocket Wrench sports 8, 9 and 10mm sockets made from forged chrome-vanadium steel in Park's classic Y-shape that offers plenty of leverage and a comfortable grip.

$15.00
The Park Tool FR-5.2GT is designed specifically for use when removing and installing cassette lockrings from thru axle hubs.
-Utilizes a 12mm guide pin to stabilize the tool during use
- Fits 12-spline cassette lockrings from Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and others (23.5mm diameter)
- Fits some Shimano and similar disc brake rotor lockrings

$15.00
Park's AWS-8 Hex Wrench Set features Bondhus balldriver ends, which facilitate use when the tool is at an angle to the bolt. This is great for working in hard-to-reach areas, such as reaching water-bottle-cage screws. The AWS-8 has 4, 5, and 6mm wrenches, which are the most common bicycle bolt sizes. Plus, its Y shape and vinyl coating provide excellent leverage and comfort.

$14.95
Because even your reliable Mavic wheels will eventually need truing, Park offers their Spoke Wrench For Mavic Wheel Systems. This comfortable, vinyl-coated, double-ended spoke wrench easily accesses and turns Mavic nipples. One end fits Mavic 6-spline, 9mm threaded eyelets and the other fits their 7-spline, 6.4mm nipples.
Page 1 of 2
Next page